-40%
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals
DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals

DIY Preamp/Amp/DAC Aluminum Enclosure Case w/Switches, Pots, & Terminals

$ 16.9

  • Brand: Unbranded
  • Color: Black
  • Compatible Brand: Universal
  • Compatible Model: Universal
  • Seller Notes: “Open box; parts were for project that never happened”
  • Type: Chassis/Enclosure

Description

[Be sure to check the prices of all three shipping options, as depending on location, the default one might not be the cheapest. Local pickup is free] Black anodized front panel is 17.25 in. wide X 2.4 in. tall X 0.26 in. thick Internal dimensions are 17 in. wide X 5 7/8 in. deep X 2 in. tall Height with feet is 2.7 in. Top and bottom cases are 14 gauge aluminum (0.068 in.) Already mounted on front panel are: - 1 ea DPDT (ON-OFF-ON) power switch; see picture for ratings - 2 ea DPDT (ON-OFF-ON) signal switch - 2 ea DPDT (ON-ON) signal switch Already mounted on rear panel are: - 5 ea red-coded RCA jack - 5 ea black-coded RCA jack Also included but not mounted are: - Illuminated pushbutton power switch (push on/push off)* - Green pushbutton switch, NO (normally open) The video shows the cosmetic condition of the front panel; note that at the bottom edge below the middle switch there's a little bit of missing anodize that I touched up with a black felt tip pen. Also, the left and right edges of the front panel got scraped in storage, so I refinished them with a surface-conditioning wheel and painted them with a marking pen. * I tested the illuminated switch for function; it lights up (upper and lower termnals), but I'm a bit puzzledby the switching terminals (the three in a horizontal row). It can be either NO or NC by using the center terminal and one of the edge terminals, but the "on" resistance is 60-ish ohms; not sure what to make of that but I'm not really an electronics guy.